An ACDelco Professional Ball Joint is a high quality replacement for many vehicles on the road today. It connects your vehicle's control arm to its steering knuckle. This ball joint features a polyurethane dust boot, a one-piece housing, and advanced bearings. It also has coated, heat-treated studs and includes all hardware. This premium aftermarket replacement component is manufactured to meet your expectations for fit, form, and function. ⚠ <bold>WARNING:</bold> Cancer and Reproductive Harm - <Underline>https://www.P65Warnings.ca.gov</Underline> CNC-machined housing for consistency and high-quality Undergoes extreme impact, wear and fatigue testing to help with quality and durability Induction hardened to match OE fatigue life Designed to perform to the application Greaseable where applicable: Allows new lubricant to flush contaminants from the assembly, reducing corrosion and wear Corrosion-resistant coating Manufactured at TS 16949-certified facilities to help with consistent high-quality Package Dimensions: 5.38 x 3.31 x 2.75 inches Package Weight: 0.1 lb Package Quantity: 1 UPC: 707773009437 ACDelco Market Indicator CA - L0: Y ACDelco Market Indicator US - L0: Y Adjustable: No Ball Joint Assembly: Yes Castle Nut Included: No Cotter Pin Hole: No Dust Boot Included: Yes FAQ - Answer 1: Yes. Replacing ball joints is not part of routine maintenance. However, they should be checked according to the manufacturer scheduled maintenance or mileage intervals, or at every oil and filter service. Most ball joints on later vehicles are sealed and do not require any grease. There are still some ball joints that should be greased every time the oil and filter is changed. Check your vehicle application for the correct service required. FAQ - Answer 2: Yes. It may change the alignment angles. Have the alignment checked after replacing any steering components. FAQ - Question 1: Does a ball joint require regular maintenance? FAQ - Question 2: Will replacing this part effect the vehicle alignment? Features & Benefits - Bullet 1: CNC-machined housing for consistency and high-quality Features & Benefits - Bullet 2: Undergoes extreme impact, wear and fatigue testing to help with quality and durability Features & Benefits - Bullet 3: Induction hardened to match OE fatigue life Features & Benefits - Bullet 4: Designed to perform to the application Features & Benefits - Bullet 5: Greaseable where applicable: Allows new lubricant to flush contaminants from the assembly, reducing corrosion and wear Features & Benefits - Bullet 6: Corrosion-resistant coating Features & Benefits - Bullet 7: Manufactured at TS 16949-certified facilities to help with consistent high-quality Good Maintenance Practices - Section 1 - Bullet 1: Inspect or have your ball joints inspected for signs of wear. Over time, lubrication inside the ball joint can dry out, leading to joint wear. Even sealed ball joints can be exposed to air, and if the ball joint's protective boot is damaged, dirt and debris could further harm the life and function of the joint. Exposure to harsh driving conditions like pot holes, bumpy road surfaces, or road salt may also cause ball joints to fail, and worn ball joints could result loss of vehicle control or tire damage. Inspect your ball joints regularly, following exposure to events that may harm the component, or when you experience signs of ball joint wear. Good Maintenance Practices - Section 1 - Bullet 2: Use new installation components. If you replace your vehicle's ball joints, make sure to use new mounting hardware, rather than reusing the old. Good Maintenance Practices - Section 1 - Bullet 3: Avoid replacing only one ball joint at a time. If you choose to replace a ball joint, you should consider replacing ball joints as a set to make front end alignment easier. Good Maintenance Practices - Section 1 - Bullet 4: Installing a new ball joint can interfere with the alignment of your vehicle. Perform a full four-wheel vehicle alignment after any ball joint replacement. Greaseable: No Material: Steel Meets or Exceeds Original Equipment Manufacture Specifications: Yes Mounting Hole Quantity: 0 Mounting Type: Press In Product Description: An ACDelco Professional Ball Joint is a high quality replacement for many vehicles on the road today. It connects your vehicle's control arm to its steering knuckle. This ball joint features a polyurethane dust boot, a one-piece housing, and advanced bearings. It also has coated, heat-treated studs and includes all hardware. This premium aftermarket replacement component is manufactured to meet your expectations for fit, form, and function. ⚠ <bold>WARNING:</bold> Cancer and Reproductive Harm - <Underline>https://www.P65Warnings.ca.gov</Underline> Programming Required: No Stud Type: Grooved Suspension Grade Type: Premium Type: Press In Country of Origin: KR